We look forward to providing you with professional services - Zhongda Leader
-
-
-
RV Cycloidal Pin Wheel Reducer
PRODUCTS
Detail
■ 120BX-RVE Outline Drawing
■ 27CBX-RVC Outline Drawing
■ 50CBX-RVC Outline Drawing
■ 100CBX-RVC Outline Drawing
■ 120CBX-RVC-P Outline Drawing
■ 200CBX-RVC Outline Drawing
■ 320CBX-RVC Outline Drawing
■ 320CA-RVC Outline Drawing
齿轮Horizontal Installation 模数Vertical Installation 齿数Size A 变位系数Size A 输入齿轮 2 12 +0.5 行星齿轮 2 42 +0.5 中心齿轮 2 81 +0.5 ■ 500CBX-RVC Outline Drawing
RVC TYPE REDUCER INSTALLATION GUIDE
In order to make fully use of RVC type reducer, it is very important to do optimal design of assembly precision, installation method, lubrication.
Please carefully read the following notes.
■ Assembly Precision
Coaxiality tolerance (a) of motor shaft and reducer is lower than 0.03mm (For models above 280BX, lower than 0.05).
Because of the poor assembly accuracy, especially easy to cause vibration and noise.
● Figure D.1: RVC series assembly precision
(A is the distance from the center of the speed reducer to the motor center)
■ Assembly Method
· RVC type reducer installed on the supporting parts of standard legend for see figure D.2. When assembly, please be sure to inject the specified amount of grease.
· Figure D.2, figure D.3 shows the "O" type of ring seal position, so please refer to the seal design.
· The structure can not be used "O" ring, please use the form C.3 liquid sealing sealant.● Example Of Low Speed Tube Assembly
Low speed tube for protection through the hollow part of the cable and the lubrication grease inside the seal reducer. Figure D.2 is a reference example for the installation of a low speed tube.
■ Output Shaft Bolt Fastening Assembly Example: Figure D.3
● Table D.1: RVC series assembly precision size table
Model Item Center Distance Tolerance Concentric Tolerance Parallelism Tolerance X a b 10CBX-RVC ±0.03 Max 0.03 Max 0.03 27CBX-RVC 50CBX-RVC 100CBX/120CBX-RVC 200CBX-RVC 320CBX-RVC 500CBX-RVC Figure D.2: Assembly example
Figure D.3: Assembly example
● Table D.2: "O" - shaped ring (I) sealing size table (mm)
Code Model 10CBX-RVC 27CBX-RVC 50CBX-RVC 100CBX/120CBX-RVC 200CBX-RVC 320CBX-RVC 500CBX-RVC 0 ring Nominal number C0-0625 C0-0634 C0-0643 S70 G95 G135 G145 Wire diameter φ2.40 φ2.40 φ3.50 φ2.00 φ3.10 φ3.10 φ3.10 Internal diameter Φ29.7 Φ42.2 φ59.6 Φ69.5 φ94.4 Φ134.4 Φ144.4 Groovesize Internal diameter d φ30.2 φ43.2 Φ60.3 φ70.0 Φ95.0 Φ135.0 Φ145.0 Width B 3.2 3.2 4.7 2.7 4.1 4.1 4.1 ● Table D.3: "O" - shaped ring (II)
Model Apply The "O"Shape Ring 10CBX-RVC AS568-048 27CBX-RVC AS568-163 50CBX-RVC AS568-169 100CBX/120CBX-RVC AS568-173 200CBX-RVC AS568-277 320CBX-RVC AS568-281 500CBX-RVC B2401-G460 ■ Central Gear, Input Gear
● Center gear, input gear precision
If the center gear, the input gear's precision is bad, can produce the noise, the
tooth gap, therefore needs to carry on the design according to the following
precision.Table D.4 center gear, the accuracy of the input gear.
■ Output shaft through hole bolt solid assembly, please ask
the company related technical personnel.
● Figure D.4: Center gear, input gear precision
● Table D.4: Center gear, input gear precision
Fit Tolerance Concentric Tolerance Central Gear Pinion Central Gear Input Gear X a Precision Grade Precision Grade Precision Grade h6 Max 0.03 GB/T100958级level GB/T100957级level GB/T100958级level ● Table D.5: Gear gap of the input gear and the big gear of the central gear (Normal line)
Model Tooth Gap(Common Law)(mm) 10CBX-RVC 0.035～0.090 27CBX-RVC 0.040～0.110 50CBX-RVC 0.050～0.130 100CBX/120CBX-RVC 0.060～0.140 200CBX-RVC 0.075～0.180 320CBX-RVC 500CBX-RVC
● Standard center gear
RVC type gear reducer with standard center gear. If you need a standard center
gear, please specify when ordering. Table D.7 gear parameters of the standard center
gear.
● Table D.6: Gear parameters of central gear pinion
Model Gear Modulus
mGear
ZCoefficient Of Variation
X10CBX-RVC 1.00 48 -0.04 27CBX-RVC 1.00 57 +0.2 50CBX-RVC 1.25 61 0 100CBX/120CBX-RVC 1.75 48 +0.3 200CBX-RVC 2.50 43 0 320CBX-RVC 2.00 78 0 500CBX-RVC 2.00 83 0
■ Tightening Torque Of Bolts
RVC type reducer using the six angle bolt, according to the table C.4 fastening
torque for fastening, bolts, please use the disc spring washer, to prevent bolt loose
and scratch the bolt seat.
● Table D.7: Gear parameters of standard center gear
Model Gear Modulus
mGear
ZCoefficient Of Variation
X10CBX-RVC 2.00 57 0 27CBX-RVC 1.25 78 0 50CBX-RVC 2.00 78 0 100CBX/120CBX-RVC 1.75 112 0 200CBX-RVC 2.00 110 0 320CBX-RVC 2.00 125 0 500CBX-RVC 2.00 150 0 ■ lubrication
· Reducer in the factory is not filled with grease, so in the installation of the reducer, be sure to fill according to the required amount of filling the recommended lubricant.
· Reducer lubricant filling amount accounts for the interior space of the 70~90%, please make sure that there are about 10% of the space is not filled up.
· Please note that the design of reducer installation needs two oil filling hole, need to seal and convenient oil filling, discharge of oil.
· Reducer sealed grease, the general replacement of oil time is about 2000 hours, please regularly check the grease of aging, pollution, and the provisions of replacement time.● Figure D.6: Lubricating oil injection position (Horizontal)
■ Install Input Gear● Figure D.5: Indicates the shape of the servo motor shaft and the installation of
the input gear sample, please refer to this diagram for design.● Figure D.5: Input gear assembly
No screw motor shaft
The motor shaft with a screw hole
The motor shaft is a conical shaft and is provided with a bolt
● Figure D.7: Lubricating oil injection position (Vertical)
● Table D.8: Grease filling amount
Model Install Horizontal Axis
(CC)
Install Vertical Axis
(CC)
Size A
(mm)
Size A
(mm)
Planetary Gear Peripheral Filling
(cc)
Center Gear Peripheral Filling
(cc)
10CBX-RVC 147 167 9.50 16.85 4 70 27CBX-RVC 266 305 10.0 21.35 10 83 50CBX-RVC 498 571 11.0 23.35 21 208 100CBX/120CBX-RVC 756 857 9.90 29.45 57 369 200CBX-RVC 1831 2076 18.5 37.70 93 642 320CBX-RVC 3536 4047 25.0 46.75 197 1275 500CBX-RVC 5934 6900 32.0 49.70 310 1803 ■ Guarantee
The warranty period and the scope of the warranty provisions are as follows.
● Warranty period
In the product catalog records of the normal assembly and lubrication under the condition of the use of the premise, the warranty period for the delivery of a year or the product running time of 2000 hours to reach the first time between the two.
● Warranty coverage
During the warranty period, the company shall be responsible for the maintenance or replacement of the product as a result of the failure of the company's product defects.
But the following conditions are not within the scope of the warranty.
1 Failure due to improper operation or use of the customer
2 Non the company's implementation of the transformation or repair of the failure of the
3 Non product causes of failure
4 Other natural disasters and other non liability of the company led to the failure ofMoreover, the warranty here refers to the warranty for this product.
For other losses caused by the failure of this product, and the equipment on the dismantling of the hours, costs, etc., are not responsible for the company.RELATED PRODUCTS
MESSAGES
If you have any questions, you can leave us a message. We have professionals to reply to you. Please fill in the correct contact information!
Contact
Ningbo Zhongda Leader Intelligent Transmission Co., Ltd.
Add.: No. 185 Xinxing 1st Road, Cixi High-tech Industrial
Development Zone, Ningbo
Tel: +86-574-63537171
Fax: +86-574-63534879
WhatsApp: +86-19136773454
E-mail: trade20@zd-motor.comFollow us on social:
Copyright © Ningbo Zhongda Leader Intelligent Transmission Co., Ltd. All Right Reserved. Powered by www.300.cn SEO Business license
-
